BRASS MARINE BEARINGS
SELECTION – Sleeve and Flanged Bearings
Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter. It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths.
The projected bearing area is the product of bearing I.D. (Shaft Diameter) x Bearing Length. Therefore the loading capability is determined by multiplying the Bearing Area x 35 psi.
Caution: If the bearing is to be shrink fitted, care is required to prevent damage to the bearing. Cool the bearing gradually. Do not cool the bearing below -20ºF (-28ºC). Dry ice or other super cool materials SHOULD NOT BE USED. Pounding the bearing in a chilled state can cause damage to the bond between the rubber and the shell material.
• Replacement clearances per Dept. Navy Ship System Command Tech Manual NAVSHIP 0901-0002. Standard practice for bore measurement is with plug gauges.
Description
| TIMCO CODE NAME | PART NO. | A SHAFT DIA. | B SHAFT DIA. | C LENGTH | D SHELL THICK | WEIGHT (LBS.) |
|---|---|---|---|---|---|---|
| KINGFISH | E03300 | 2″ | 3″ | 8″ | 1/8″ | 3.88 |
| LAMPREY | E03350 | 2″ | 3″ | 1O” | 1/8″ | 4.85 |
| MACKEREL | E03400 | 2 1/8″ | 2 15/16″ | 8 1/2″ | 1/8″ | 3.69 |
| MANTA | E03500 | 2 1/8″ | 3 1/8″ | 8 1/2″ | 1/8″ | 4.50 |
| MARLIN | E03600 | 2 1/4″ | 2 15/16″ | 9″ | 1/8″ | 3.94 |
| MARGATE | E03650 | 2 1/4″ | 3″ | 9″ | 1/8″ | 4.980 |
| MINNOW | E03700 | 2 1/4″ | 3 1/8″ | 9″ | 1/8″ | 4.44 |
| MUOFISH | E03800 | 2 1/4″ | 3 3/8″ | 9″ | 1/8″ | 5.44 |
| MULLET | E03900 | 2 3/8″ | 3 3/8″ | 9 1/2″ | 1/8″ | 5.44 |
| MUSKY | E04000 | 2 1/2″ | 3 1/8″ | 1O” | 1/8″ | 4.63 |
| PERCH | E04100 | 2 1/2″ | 3 318″ | 1O” | 1/8″ | 5.50 |
| PIKE | E04150 | 2 1/2″ | 3 1/2″ | 1O” | 1/8″ | 6.47 |
| PICKEREL | E04200 | 2 5/8″ | 3 318″ | 10 112″ | 1/8″ | 5.75 |
| PlCUDA | E04300 | 2 3/4″ | 3 318″ | 11″ | 1/8″ | 5.63 |
| PINFISH | E04400 | 2 3/4″ | 3 314″ | 11″ | 1/8″ | 6.88 |
| PORGY | E04500 | 2 718″ | 3 314″ | 11 112″ | 1/8″ | 7.13 |
| RAY | E04600 | 3″ | 3 314″ | 12″ | 1/8″ | 7.06 |
| REDFIN | E04700 | 3″ | 4″ | 12″ | 1/8″ | 7.94 |
| REDFISH | E04800 | 3 1/8″ | 4 1/4″ | 12 1/2″ | 1/8″ | 9.25 |
| ROCKFISH | E04900 | 3 1/4″ | 4″ | 13″ | 1/8″ | 8.136 |
| SAILFISH | E05000 | 3 1/4″ | 4 1/4″ | 13″ | 1/8″ | 9.38 |
| SALMON | E05100 | 3 3/8″ | 4 1/2″ | 13 112″ | 1/8″ | 10.63 |
| SANOFISH | E05200 | 3 1/2″ | 4 1/4″ | 14″ | 1/8″ | 9.56 |
| SAWFISH | E05300 | 3 112″ | 4 1/2″ | 14″ | 1/8″ | 10.25 |
| SCULPIN | E05400 | 3 518″ | 4 1/2″ | 14 1/2″ | 1/8″ | 10.81 |
| SHAO | E05500 | 3 3/4″ | 4 1/2″ | 15″ | 1/8″ | 11.00 |
| SHARK | E05600 | 3 314″ | 5″ | 15″ | 3/16″ | 17.56 |
| SILVERFISH | E05700 | 3 314″ | 5 1/4″ | 15″ | 3/16″ | 18.19 |
| SMELT | E05800 | 3 718″ | 5 1/4″ | 15 1/2″ | 3/16″ | 20.00 |
| SNAPPER | E05900 | 4″ | 5″ | 16″ | 3/16″ | 18.25 |
| SOCKEYE | E06000 | 4″ | 5 1/4″ | 16″ | 3/16″ | 19.63 |
| SPEARFISH | E06100 | 4 1/8″ | 5 1/4″ | 16 1/2″ | 3/16″ | 20.06 |
| SQUIT | E06200 | 4 1/4″ | 5 1/2″ | 17” | 3/16″ | 22.00 |
| STREAKER | E06300 | 4 318″ | 5 314″ | 17 1/2″ | 3/16″ | 24.31 |
| SUCKER | E06400 | 4 112″ | 5 1/2″ | 18″ | 3/16″ | 22.00 |
| SUNFISH | E06500 | 4 1/2″ | 5 314″ | 18″ | 3/16″ | 24.63 |
| SWORDFISH | E06600 | 4 518″ | 6 1/8″ | 18 1/2″ | 1/4″ | 34.00 |
| TARPON | E06700 | 4 314″ | 6 1/8″ | 19″ | 1/4″ | 34.00 |
| TROUT | E06800 | 4 718″ | 6 1/8″ | 19 1/2″ | 1/4″ | 33.00 |
| WAHOO | E06900 | 5″ | 6 1/8″ | 20″ | 1/4″ | 35.00 |
| WALLEYE | E07000 | 5″ | 6 1/2″ | 20″ | 1/4″ | 39.00 |
| WANDTAIL | E07100 | 5 1/4″ | 6 314″ | 21″ | 1/4″ | 44.00 |
| WAP | E07200 | 5 1/4″ | 7″ | 21″ | 1/4″ | 48.00 |
| WARFISH | E07300 | 5 3/8″ | 6 314″ | 21 112″ | 1/4″ | 57.00 |
| WARSAW | E07400 | 5 3/8″ | 7″ | 21 1/2″ | 1/4″ | 62.00 |
| WHITEFISH | E07500 | 5 112″ | 7″ | 22″ | 1/4″ | 59.00 |
| WINOFISH | E07600 | 5 518″ | 7″ | 22 1/2″ | 1/4″ | 44.50 |
| YELLOWTAIL | E07700 | 5 3/4″ | 7″ | 23″ | 1/4″ | 48.00 |
| YOWLING | E07800 | 5 718″ | 7 1/2″ | 24″ | 1/4″ | 52.00 |
| ZANCLUS | E07900 | 6 “ | 7 1/2″ | 24″ | 1/4″ | 55.00 |
| ZEBRAFISH• | E07950 | 6 1/2″ | 8 3/8″ | 30″ | 7/16 | 150.00 |
TOLERANCES – Sleeve and Flanged Bearings
| SHAFT DIA. | STD. MARINE SHAFT CLEARANCE | IND. PUMP SHAFT CLEARANCE | O.D. TOL. | TIR | *REPLACEMENT CLEARANCE | ||
|---|---|---|---|---|---|---|---|
| INCHES | mm. | SLEEVE | FLANGE | ||||
|
3/4 7/8 1 1 1/8 1 1/4 1 3/8 |
19.050 22.225 25.400 28.575 31.750 34.925 |
+ .003/.008 .08/.20mm |
+ .002/.007 .05/.18mm |
± .001 .03mm |
.006 .15mm |
+.070 1.78mm |
|
|
1 1/2 1 5/8 1 3/4 1 7/8 |
38.100 41.275 44.450 47.625 |
+ .004/.010 .10/.25mm |
+ .003/.009 .08/23mm |
+.081 2.06mm |
|||
|
2 2 1/8 2 1/4 2 3/8 |
50.500 53.975 57.150 60.325 |
+ .006/.012 .15/30mm |
+ .004/.010 .10/.25mm |
+.091 2.31mm +.100 2.54mm |
|||
|
2 1/2 2 5/8 2 3/4 2 7/8 3 |
63.500 66.675 69.850 73.025 76.200 |
+ .007/.014 .18/.36mm |
+ .005/.011 .13/.28mm |
+ .107 2.72mm |
|||
|
3 1/8 3 1/4 3 3/8 3 1/2 3 5/8 3 3/4 |
79.375 82.550 85.725 88.900 92.075 95.250 |
+ .008/.015 .20/.38mm |
+ .007/.014 .18/.36mm |
± .002 .05mm |
± .003 .08mm |
+ .120 3.05mm |
|
|
3 7/8 4 4 1/8 4 1/4 |
98.425 101.600 104.775 107.950 |
+ .010/.017 .25/.43mm |
|||||
|
4 3/8 4 1/2 4 5/8 4 3/4 4 7/8 |
111.125 114.300 117.475 120.650 123.825 |
+ .012/.019 .30/.48mm |
+ .008/.015 .20/.38mm |
± .004 .10mm |
.008 .20mm |
+ .142 3.61mm |
|
|
5 5 1/4 5 3/8 |
127.000 133.350 136.525 |
+ .015/.023 .38/.58mm |
+ .008/.017 .20/.43mm |
||||
|
5 1/2 5 5/8 5 3/4 5 7/8 |
139.700 142.875 146.050 149.225 |
+ .017/.025 .43/.64mm |
+ .008/.017 .20/.43mm |
± .002 .05mm |
± .004 .10mm |
.008 .20mm |
+ .142 3.61mm |
| 6 | 152.400 |
+ .020/.029 .51/.74mm |
+ .153 3.89mm |
||||
| 6 1/4 | 158.750 |
± .005 13mm |
± .005 .13mm |
.010 25mm |
|||
|
6 1/2 6 3/4 |
165.100 171.450 |
+ .022/.032 .56/.81mm |
+ .008/.018 .20/.46mm |
+ .164 4.17mm |
|||
|
7 7 1/4 |
177.800 184.150 |
+ .024/.034 .61/.86mm |
|||||
| 7 1/2 | 190.500 |
+ .025/.035 .64/.89mm |
|||||
| 7 3/4 | 196.850 | ||||||
| 8 | 203.200 |
+ .027/.037 .69/.94mm |
+ .175 4.45mm |
||||
| 8 1/4 | 209.550 |
.012 .30mm |
|||||
|
8 1/2 8 3/4 |
215.900 222.250 |
+ .028/.040 .71/1.02mm |
+ .009/.021 .23/.53mm |
||||
|
9 9 1/4 9 1/2 9 3/4 |
228.600 234.950 241.300 247.650 |
+ .030/.042 .76/1.07mm |
+ .185 4.70 |
||||
|
10 10 1/4 10 1/2 10 3/4 |
254.000 260.350 266.700 273.050 |
+ .032/.044 .81/1.12mm |
± .006 .15mm |
+ .196 4.98mm |
|||
|
11 11 1/4 |
279.400 285.750 |
+ .034/.048 .86/1.22mm |
+ .009/.024 .23/.61mm |
+ .206 5.23mm |
|||
|
11 1/2 11 3/4 12 |
292.100 298.450 304.800 |
+ .035/.050 .89/1.27mm |
+ .216 5.49mm |
||||
|
12 1/4 12 1/2 12 3/4 |
311.150 317.500 323.850 |
.014 .36mm |
|||||
| 13 | 330.200 |
+ .037/.052 .94/1.32mm |
+ .226 5.74mm |
||||
| 13 1/4 | 336.550 |
± .008 .20mm |
|||||
|
13 1/2 13 3/4 14 14 1/4 14 1/2 |
342.900 349.250 355.600 361.950 368.300 |
+ .040/.055 1.02/1.47mm |
+ .235 5.97mm |
||||
|
14 3/4 15 |
374.650 381.000 |
+ .042/.058 1.07/1.47mm |
+ .009/.025 .23/.64mm |
||||
None.
