Model 4WP2T8-2000-8

WORM GEAR POWER WINCHES

4WP2 / 4WP2T8 / 4WP2TC

Up to 2000 lb. capacity

  • 115 Volt Single Phase Electric Motor includes power cord with grounded plug and a momentary contact-type push button pendant control on a control cord.
  • Machine Cut Worm Gears provide accurate operation and long lasting service.
  • Enclosed Oil Bath provides continuous lubrication of gears to minimize wear. Oil seals keep oil in and dirt out.
  • Internal Mechanical Brake provides positive load control for lifting and lowering operations.
  • Ball Bearings and self-aligning bronze bearings provide smooth and efficient operation.
  • Pressure Plate on series 4WP2T8 only, applies pressure to drum and wire rope to help maintain uniform winding.
  • Dual Function Cable Anchor for quick disconnect of wire rope with swaged ball fitting, or recessed cable anchor with set screw for wire rope with unfinished end.
  • Mounting Options include floor, wall, or ceiling.
  • Two-year Limited Warranty
  • Cast Aluminum construction, for lightweight strength.
  • Corrosion Resistant durable paint finish protects against corrosion in harsh environments.
  • Large Diameter Drums minimize wear to the wire rope and help extend its life.
  • Clutch Model allows operator to manually disengage the drum to rapidly unwind wire rope. Clutch models do not include pressure plates.

 

Category:

Description

Series 4WP2 and 4WP2T8 – Performance Characteristics 

LOAD RATING (LB.) LINE SPEED (FPM) DRUM CAPACITY (FT)1
SERIES DESCRIPTION MOTOR HP AMPS FULL LOAD 1ST LAYER MID DRUM FULL DRUM WIRE ROPE DIA. (IN) 1ST LAYER MID DRUM 1ST LAYER MID DRUM FULL DRUM APPROX SHIP WT. (LB.)
4WP22 includes controls 1.3 16 2000 1200 1200 1/4 8 13 11 35 77 85
4WP2T8-2000-84 includes controls 1.3 16 2000 1200 800 1/4 8 19 19 130 280 101
ATLAS winch – 5.5″ drum – for pulling or lifting 5/16 8 19 15 85 190
4WP2TC-2000-84 includes controls 1.3 16 2000 1200 800 1/4 8 19 12 87 190 106
clutch model – 5.5″ drum – for horizontal pulling only

 

Motor Options – standard motor is 115/1/60 VAC TEFC, for other configurations add motor code to model number when ordering.
Example: 4WP2T8-2000-8-PN (pneumatic winch)
A5 115 volt 1 phase – no controls or power cord – TENV
B5 230 volt 1 phase – no controls or power cord – TEFC
D5 230 volt 3 phase – no controls or power cord – TEFC
E5 460 volt 3 phase – no controls or power cord – TEFC
F all other voltages or hertz
PN 8-vane air motor w/controls (mounted)

Options & Accessories

MODEL DESCRIPTION APPROX. SHIP WT.
EL1CS7 NEMA 1 control switch – mounted and wired 3 lb.
EL1CSW7 NEMA 4 watertight control switch – mounted and wired 7 lb.
TPL-4WP2 Two Part Line Kit – not available for 4WP2 Series 4 lb.

 

1 Actual drum capacities may be 25-30% less, due to nonuniform winding. Tension in wire rope will also affect drum capacity.

2 Model 4WP2, 115 VAC motor includes 8 ft power cord with grounded plug, and push button pendant control on 6 ft cord.

3 Please contact TIMCOfor firm fixed price and delivery.

4 For 4WP2T8 & 4WP2TC, 115 VAC motor includes 16 ft power cord with grounded plug, and push button pendant control on 16 ft cord.

5 Controls are sold separately for all non-standard electric motors (A, B, D, and E).

6 Please contact TIMCO for firm fixed price and delivery.

7 Controls for 115 volt, single phase, 60 cycle include an 8 ft power
cord with grounded plug.

Series 4WP2 and 4WP2T8 – Dimensions (in)

MODEL NUMBER A1 B1 C D E F H1 J K M N P R S (HOLE DIA.)
4WP2 15.63 17.28 1.72 12.84 1.72 3.75 13.50 4.00 0.41
4WP2T8-2000-8 16.62 17.80 2.75 4.88 1.44 6.43 14.25 2.25 5.81 10.25 1.25 7.00 11.38 0.41
4WP2TC-2000-8 17.34 17.80 4.02 4.88 2.16 6.43 14.25 2.25 5.81 10.25 1.25 7.00 11.38 0.41

Dimensions are for reference only and subject to change without notice.
1 Dimensions A, B and H may vary with motor selection.

Series 4WP – Drum Dimensions

MODEL EXTENSION DRUM DIAMETER FLANGE DIAMETER DRUM WIDTH FLEET ANGLE DISTACE4
4WP2 2.50 in. 5.00 in. 5.00 in. 8 ft.
4WP2T8-2000-8 2.50 in. 7.00 in. 8.00 in. 13 ft.
4WP2TC-2000-8 2.50 in. 7.00 in. 5.50 in. 9 ft.

Dimensions are for reference only and subject to change without notice.
4 Recommended minimum distance between drum and lead sheave for smooth drum.

Wire rope assemblies sold separately

Options and Accessories

  • Emergency Hand Crank for manual operation in case of power failure. Does not include handle.
  • Two Part Line Kit to convert to double line rigging.  Not available for 4WP2 Series.
  • Rotary Limit Switches for secondary shut-off to limit load travel in one or two directions.  Not available on clutch models.
  • Special Motors and Controls including severe duty and explosion proof.
  • Special Finishes for hazardous environments.
  • Torque Limiters as part of the motor controls on electric models.

Important:

It is the owner’s or operator’s responsibility to determine the suitability of the equipment to its intended use. Study all applicable codes, manuals and regulations.

Be sure to read the Owner’s Manual supplied with the equipment before operating it.