View cart “GW SERIES WALL MOUNT” has been added to your cart.
Model 4WP2D8-1500-40

HIGH SPEED WORM GEAR POWER WINCHES

4WP2D8 / 4WP2DC

Up to 1500 lb. capacity

  • Direct Drive Design delivers high speed operation in both directions, even under full load.
  • Machine Cut Bronze Worm Gears provide accurate operation and long lasting service.
  • Enclosed Oil Bath provides continuous lubrication of gears to minimize wear. Oil seals keep oil in and dirt out.
  • Internal Mechanical Brake provides positive load control for lifting and lowering operations.
  • Ball Bearings and self-aligning bronze bearings provide smooth and efficient operation.
  • Pressure Plate applies pressure to drum and wire rope to help maintain uniform winding. Not available on clutch models.
  • Dual Function Cable Anchor for quick disconnect of wire rope with swaged ball fitting, or recessed cable anchor with set screw for wire rope with unfinished end.
  • Mounting Options include floor, wall or ceiling.
  • Two-year Limited Warranty
  • Cast Aluminum construction, for lightweight strength.
  • Corrosion Resistant durable paint finish protects against corrosion in harsh environments.
  • Large Diameter Drums minimize wear to the wire rope and help extend its life.
  • Clutch Model allows operator to manually disengage the drum to
    rapidly unwind wire rope. Clutch models do not include pressure plates.
Category:

Description

Series 4WP2D – Performance Characteristic

When ordering, please indicate Model Number and Extensions
Examples: 4WP2D8-800-26-A (without clutch); 4WP2DC-800-40-A (with clutch)

MODEL NUMBER EXTENSIONSLOAD RATINGS (LB.)LINE SPEED (FPM)DRUM CAPACITY (FT.)1
MODEL NUMBERLOAD RATINGLINE SPEEDMOTOR CODESMOTOR HP1ST LAYERMID DRUMFULL DRUMWIRE ROPE DIA.(IN.)1ST LAYERFULL DRUM1ST LAYERMID DRUMFULL DRUMAPPROX. SHIP WT. (LB.)2
High Speed Atlas winches for lifting or pulling
4WP2D880026A,B,D,E18004603301/4266519130280100
4WP2D880040D,E1.58004603301/4409719130280100
4WP2D8150026D,E215009006001/4266519130280100
4WP2D8150040D,E315009006001/4409719130280100
High Speed Clutch Models for HORIZONTAL PULLING ONLY
4WP2DC80026A,B,D,E18004603001/426651287190100
4WP2DC80040D,E1.58004603001/440971287190100
4WP2DC150026D,E215009006001/426651287190100
4WP2DC150040D,E315009006001/440971287190100

1  Actual drum capacities 25-30% less, due to nonuniform winding. Wire rope tension will also affect drum capacity.
2  Weight may vary with motor.

MODELDESCRIPTION115/1/605230/1/60230/3/60460/3/60
EL1CSNEMA 1to 1.5 hpto 2 hpto 3 hpto 3 hp
EL2CSNEMA 1to 1.5 hpto 3 hpto 5 hpto 7.5 hp
EL1CSWNEMA 4to 1.5 hpto 2 hpto 3 hpto 3 hp
EL2CSWNEMA 4to 1.5 hpto 3 hpto 5 hpto 7.5 hp
TPL-4WP2Two Part Line Kit

5 Controls for 115V single phase motors up to 1 hp, include an 8 ft power cord with grounded plug.


Series 4WP2D – Dimensions (in) 

SERIESA1B1CDEFH1JKMNPRS (HOLE DIA.)
4WP2D817.5021.002.755.001.509.5012.752.255.8110.251.257.0011.50.41
4WP2DC19.0021.004.005.003.509.5012.752.255.8110.251.257.0011.50.41

Dimensions are for reference only and subject to change without notice.
1 Dimensions A, B and H may vary with motor selection.


Series 4WP2D – Drum Dimensions

MODEL EXTENSIONDRUM DIAMETERFLANGE DIAMETERDRUM WIDTHFLEET ANGLE DISTANCE
4WPD82.50 in.7.00 in.8.00 in.13 ft.
4WPDC2.50 in.7.00 in.5.50 in.9 ft.

Dimensions are for reference only and subject to change without notice.
4 Recommended minimum distance between drum and lead sheave for smooth drum.

Options and Accessories

  • Emergency Hand Crank for manual operation in case of power failure. Does not include handle.
  • Two Part Line Kit to convert to double line rigging.
  • Rotary Limit Switches for secondary shut-off to limit load travel in one or two directions. Not available on clutch models.
  • Special Motors and Controls including severe duty and explosion proof.
  • Special Finishes for hazardous environments.
  • Torque Limiters as part of the motor controls on electric models.

Important: 

It is the owner’s or operator’s responsibility to determine the suitability of the equipment to its intended use. Study all applicable codes, manuals and regulations.

Be sure to read the Owner’s Manual supplied with the equipment before operating it.