HIGH SPEED WORM GEAR POWER WINCHES

4WP2D8 / 4WP2DC

Up to 1500 lb. capacity

Direct Drive Design delivers high speed operation in both directions, even under full load.
Machine Cut Bronze Worm Gears provide accurate operation and long lasting service.
Enclosed Oil Bath provides continuous lubrication of gears to minimize wear. Oil seals keep oil in and dirt out.
Internal Mechanical Brake provides positive load control for lifting and lowering operations.
Ball Bearings and self-aligning bronze bearings provide smooth and efficient operation.
Pressure Plate applies pressure to drum and wire rope to help maintain uniform winding. Not available on clutch models.
Dual Function Cable Anchor for quick disconnect of wire rope with swaged ball fitting, or recessed cable anchor with set screw for wire rope with unfinished end.
Mounting Options include floor, wall or ceiling.
Two-year Limited Warranty
Cast Aluminum construction, for lightweight strength.
Corrosion Resistant durable paint finish protects against corrosion in harsh environments.
Large Diameter Drums minimize wear to the wire rope and help extend its life.
Clutch Model allows operator to manually disengage the drum to
rapidly unwind wire rope. Clutch models do not include pressure plates.

Category: Winches

Description

Series 4WP2D – Performance Characteristic

When ordering, please indicate Model Number and Extensions
Examples: 4WP2D8-800-26-A (without clutch); 4WP2DC-800-40-A (with clutch)

	MODEL NUMBER EXTENSIONS				LOAD RATINGS (LB.)				LINE SPEED (FPM)		DRUM CAPACITY (FT.)¹
MODEL NUMBER	LOAD RATING	LINE SPEED	MOTOR CODES	MOTOR HP	1ST LAYER	MID DRUM	FULL DRUM	WIRE ROPE DIA.(IN.)	1ST LAYER	FULL DRUM	1ST LAYER	MID DRUM	FULL DRUM	APPROX. SHIP WT. (LB.)²
High Speed Atlas winches for lifting or pulling
4WP2D8	800	26	A,B,D,E	1	800	460	330	1/4	26	65	19	130	280	100
4WP2D8	800	40	D,E	1.5	800	460	330	1/4	40	97	19	130	280	100
4WP2D8	1500	26	D,E	2	1500	900	600	1/4	26	65	19	130	280	100
4WP2D8	1500	40	D,E	3	1500	900	600	1/4	40	97	19	130	280	100
High Speed Clutch Models for HORIZONTAL PULLING ONLY
4WP2DC	800	26	A,B,D,E	1	800	460	300	1/4	26	65	12	87	190	100
4WP2DC	800	40	D,E	1.5	800	460	300	1/4	40	97	12	87	190	100
4WP2DC	1500	26	D,E	2	1500	900	600	1/4	26	65	12	87	190	100
4WP2DC	1500	40	D,E	3	1500	900	600	1/4	40	97	12	87	190	100

¹ Actual drum capacities 25-30% less, due to nonuniform winding. Wire rope tension will also affect drum capacity.
² Weight may vary with motor.

MODEL	DESCRIPTION	115/1/60⁵	230/1/60	230/3/60	460/3/60
EL1CS	NEMA 1	to 1.5 hp	to 2 hp	to 3 hp	to 3 hp
EL2CS	NEMA 1	to 1.5 hp	to 3 hp	to 5 hp	to 7.5 hp
EL1CSW	NEMA 4	to 1.5 hp	to 2 hp	to 3 hp	to 3 hp
EL2CSW	NEMA 4	to 1.5 hp	to 3 hp	to 5 hp	to 7.5 hp
TPL-4WP2	Two Part Line Kit

⁵ Controls for 115V single phase motors up to 1 hp, include an 8 ft power cord with grounded plug.

Series 4WP2D – Dimensions (in)

SERIES	A¹	B¹	C	D	E	F	H¹	J	K	M	N	P	R	S (HOLE DIA.)
4WP2D8	17.50	21.00	2.75	5.00	1.50	9.50	12.75	2.25	5.81	10.25	1.25	7.00	11.50	.41
4WP2DC	19.00	21.00	4.00	5.00	3.50	9.50	12.75	2.25	5.81	10.25	1.25	7.00	11.50	.41

Dimensions are for reference only and subject to change without notice.
¹ Dimensions A, B and H may vary with motor selection.

Series 4WP2D – Drum Dimensions

MODEL EXTENSION	DRUM DIAMETER	FLANGE DIAMETER	DRUM WIDTH	FLEET ANGLE DISTANCE
4WPD8	2.50 in.	7.00 in.	8.00 in.	13 ft.
4WPDC	2.50 in.	7.00 in.	5.50 in.	9 ft.

Dimensions are for reference only and subject to change without notice.
⁴ Recommended minimum distance between drum and lead sheave for smooth drum.

Options and Accessories

Emergency Hand Crank for manual operation in case of power failure. Does not include handle.
Two Part Line Kit to convert to double line rigging.
Rotary Limit Switches for secondary shut-off to limit load travel in one or two directions. Not available on clutch models.
Special Motors and Controls including severe duty and explosion proof.
Special Finishes for hazardous environments.
Torque Limiters as part of the motor controls on electric models.

Important:

It is the owner’s or operator’s responsibility to determine the suitability of the equipment to its intended use. Study all applicable codes, manuals and regulations.

Be sure to read the Owner’s Manual supplied with the equipment before operating it.

HIGH SPEED WORM GEAR POWER WINCHES

4WP2D8 / 4WP2DC

Description

Important:

Related Products